MDO? AC? Plywood?
Updated: Nov 5, 2023
There are these options for the surface to paint your BQ on. Which is the best to use?

How do you prepare each surface? Which last the longest? Which is least expensive and where can you find it? Let me see if I can address each one of these questions that are asked so often by new crafters and experienced artist both.
Let's first talk about plywood. It is the easiest to find and can be purchased anywhere that sells building materials. It is readily available in different grades and thickness at big box stores such as Lowes, Home Depot and Menards. Prices vary but it is less expensive than MDO or AC. That is the only perk about it when it comes to this application.
Plywood is grainy and takes a measurable amount of prep to prepare it for painting. First you may have to use a wood filler in any deep groves or cracks, sand the entire surface to a baby smooth finish. If you do not do this, tape will not lay properly and can cause bleeding of the paint and that is stressing. Once this is done, I recommend two coats of primer.
Plywood is also the last durable product to use. As it weathers, the wood grain has a tendency to lift and bleed through the surface. This can cause the elements to penetrate into the surface, regardless if sealed or not. Also, if you do not frame your plywood in and caulk it, the layers of wood can separate and deteriorate.
MDO is the preferred surface for most artists, including myself. MDO is multi-density overlay board. It is a sheet of plywood base that is chemically treated to resist moisture and there is an overlay applied to the surface that resembles kraft paper. It is very smooth and can be one sided or two sided. It is a waterproof surface once painted and sealed. It can be found in several thickness and most use the 3/8" for anything 2-4' sizes. Some use the 1/2' or 3/4" for larger BQ's.
MDO does require little prep. It is recommended to caulk and trim in the edges but some artist choose not to. Personal decision but I do finish mine. I have a video tutorial on this in another post. Also only a single coat of primer is needed. Multiple coats of primer can cause paint issues like bubbling, longer drying time and chemical reaction to a sealer. (check out the video on primer on the blog). Paint applies so perfectly on this product and makes taping crisp lines a breeze with minimal touch ups. It is also recommend to use an interior latex paint with a sealer on this product.
MDO has become increasingly hard to find since the pandemic. It is a specialty product and the large box stores do not carry it. No matter what they tell you - MDF IS NOT MDO. MDF will just melt when wet. My supplier has not been able to get it since Oct and the price at that time had increased from $65 per sheet to $95. Some places are charging up to $125 per sheet if they can get it. My supplier cuts it to size for me and for the best cuts, a panel saw is the best. A local cabinet shop can cut it for you also.
Aluminum Composite (AC) is the next choice preferred by artist. Many like this because it is light weight, easy to manage and requires the least prep work. That is attractive to even myself. Customers like that it is light weight especially if hanging on siding. I have had to make the switch to AC because of availability. I do order from a supplier two hours away from me. I purchase 26 sheets at a time, cut to size and it comes by freight carrier so shipping is expensive. I may be picking up the next order myself because shipping may bring me up for air. Your local sign company or internet search for suppliers is a place to start to find a source close to you.
I use the 3mm thickness but it comes in various thickness. To prepare this surface for painting is fairly easy. I sand this with a 220 grid sanding block to scuff the surface. Some use steel wool, either is fine. I then wipe this down with a alcohol wipe just to get the dust off. Then it should be primed with a single coat of primer. Once primed, you proceed with drawing and painting your pattern.
The only draw back I have found with the AC is that the paint will scratch off with some effort so you should be careful with it until the sealer is applied. The sealer tends to harden the paint and protect from this. Taping off is really smooth but you have to use proper technique when pulling tape. (video on this also in another post) If you are not careful and let the paint fully dry, pull away from your paint line, then it can lift the paint up.
AC is compatible with MDO pricing in some areas. I am paying $62 a sheet plus shipping. It makes for a long lasting BQ just as MDO does. If you need to cut your AC to size, it is quite easy to do. Use a straight edge and score the cut with a sharp razor knife and apply even pressure and it will snap into. I think there are several Youtube videos on this.
I hope this helps you to choose the surface that meets your needs. I know there are many opinions and recommendation and this information is based on my actual experience using all three products.
Remember, I am always here to help answer any questions!
Carry on the Addiction,
Talara





What do I use, instead of varnish, if I want to keep the wood grain?
So where is the links to find the supplies or boards
The MDO that I got yesterday has big bold black lettering on the paper side, so do you think the Kilz primer will cover that or will it bleed through? Maybe just prime the paper side and paint the already primed side. Your thoughts is appreciated. Thanks,
I haven’t started painting BQ yet but am strongly considering AC due to easier to get materials…one thing I have come across is matte or glossy AC…which would your recommend and why that choice? Thank you for your time!
Finally got my three 2x2's of the AC from Home Depot (free shipping because of dollar amount.) Would AC work for a double sided BQ? Also, didn't I see somewhere that you have to peel off something on the AC before you can use it too right? Where did I see that?
Thanks for all you do!